◎ Newly developed print head
The UJV500-160 can print at high speeds up to 60 m2/h. A speed of 24 m2/h can be reached while printing with white ink. The number of print heads and nozzles has been updated. The six 2 inch print heads are aligned in a staggered array, which is optimized to eject ink effectively.
* 1 head=1,280 nozzles (320 nozzles X 4 rows), In total: 7,680 nozzles (1,280 nozzle X 6 heads)
Print Speed
* The print speeds above are the results of printing on media with a 1,610mm width.
Depending on the firmware setting, the print speeds above may not be reproduced.
◎ Newly developed LED-UV Unit
Curing efficiency has been improved due to renovating the LED-UV unit. In addition to being long-lasting and energy-saving, LED UV lamps do not generate excessive heat. This enables printing onto a wider range of materials, including heat-sensitive substrates, without media deformation.
In addition to the normal pattern, you can select "MAPS" which effectively reduces banding. MAPS implements printing in a gradational mask pattern and diminishes the appearance of banding.
* Depending on the setting of MAPS, print speed varies.
(MAPS = Mimaki Advanced Pass System)
Variable dot printing ejects ink drops in 3 different dot sizes. This smooth gradation without granular appearance is even achieved with 4-color printing.
By pulling media down vertically, feeding errors are reduced, thus increasing print stability. This allows for continuous printing onto large media with a maximum roll diameter of 300mm and weight of 60kg. The high speed printing of the UJV500-160 enables high productivity.
Additionally, the take up unit is positioned more towards the front than conventional printers, allowing media to be set more easily.
Previously, repairs by service personnel were required when nozzle clogging was not corrected by cleaning. Now, the nozzle recovery system allows for printing to proceed as if the nozzle is not clogged, without slowing down the print speed.
*The recoverability of this function is limited.
LUS-150 has the best curing property for high speed printing. This ink offers improved curing times resulting in a less tactile sticky feeling. This ink is flexible up to 150% resulting in increased elasticity and bending performance on a wide variety of media and substrates with little cracking. Additionally, white ink allows for printing on transparent film for window graphics.
* LUS = LED UV Stretchable
* As the flexibility of LUS-150 ink may vary according to the substrate, please verify your substrate in advance.
UV-Curable ink
A 3-layer print of color, white and color can be performed simultaneously. Printing a base layer of white ink reproduces the natural beauty of process colors that are printed on transparent substrates, with high precision and no multi-pass color registration shift.
By periodically circulating white ink in the line, pigment deposition is prevented. This accomplishes stable production and reduction of ink discharge and waste.
* MCT (Mimaki Circulation Technology) works only with white ink.
Achieve high speed, high quality printing with the UJV500-160, along with guaranteed outdoor durability from 3M’s “3M™ MCS™ Warranty”. The long term warranty and the 200% flexibility ideal for curved surface applications open up new possibilities in the inkjet signage industry.
* The 3M warranty is only applicable for Japan.
■merit 1
Having an outdoor durability allows for installation of printed materials in places where regular maintenance is not possible, without worrying about deterioration.
■merit 2
The new UV ink ”LUS-200”, which has been jointly-developed with 3M, can stretch up to 200% after curing. Since stretching will not crack the image, the LUS-200 ink is ideal for applications with curved surfaces such as vehicle wraps.
・LUS = LED UV Stretchable
・The flexibility of LUS-200 inks may vary according to the substrate, please verify your substrate in advance.
UV-Curable ink
【About the 3M™ MCS™ Warranty】
When finished products are printed using the UJV500-160 printer and LUS-200 ink onto media specified by 3M, and are installed properly according to 3M’s instructions, the quality is guaranteed for the warranty period.
① Outdoor durability is guaranteed.
② When a warranty letter is needed, an application must be completed. Following this application, a screening by 3M will be performed. If approved, issuance of the warranty certificate will follow.
* For further details, please refer to 3M’s guide “Certificate of 3M™ MCS™ Warranty Program”.
* Warranty periods vary based on type of application, type of media, and graphic protection.
◎ Low VOCs & Ozone-Free
UV curing generates minimal VOCs. LED UV ink is ozone-free.
◎ Power saving, long lasting LED–UV lamp
The LED-UV lamp generates very little heat. Unlike metal halide lamps, LED-UV lamps light up only where the image is printed, which leads to cost-effective production. As the life of the lamp is very long, both environmentally-friendly and economical production is supported.
◎ Ink supplied in bottles
Each UV ink is supplied in a high-capacity bottle instead of a cartridge. This economical and ecological package contributes to reduce the amount of industrial waste and running costs.
MDM, which removes nozzle trouble caused by bubbles in the ink, is employed.
Ink that has not been degassed is supplied in bottles (the printer handles the degassing), both of which enable lower ink costs.
※MDM = Mimaki Degassing Module
UJV500-160 | ||
---|---|---|
Head | On-demand Piezo head (6 printheads with 3 staggered configuration) | |
Print width | 297mm ~ 1,610mm | |
Print resolution | 300dpi、600dpi、900dpi、1,200dpi | |
Ink | Type | UV curable ink: LUS-120(C、M、Y、K、W) UV curable ink: LUS-150(C、M、Y、K、Lc、Lm、W) UV curable ink: LUS-200(C、M、Y、K、W) |
Supply system | Supplied by 2L Ink Station | |
Ink Circulation (*1) | White ink circulation by MCT (Mimaki Circulation Technology) | |
Ink degassing module | Equipped with MDM (Mimaki Degassing Module) | |
Media | Size | 1,620 mm or less |
Roll weight | 60 kg or less | |
Thickness | 0.1 mm ~ 1 mm (The thickness in which media can be feeded) | |
Roll diameter | φ300 mm or less | |
Roll inside diameter | 2-inch、3-inch | |
Cutter | Y-direction cutter after head section | |
Media heater | 3-way inteligent heater (Pre/Print/After) | |
Print gap | 1.5 mm ~ 7.0 mm (Configurable by users, automatic recognition of the thickness) |
|
Print accuracy | Absolute accuracy | ± 0.3 mm or ± 0.3% from specified print distance |
Repeatability | ± 0.2 mm or ± 0.1% from specified print distance | |
UV unit | Head unit | Equipped with UV LED (Lifetime: about 5,000 hours) *2 |
Post cure unit | Equipped with fluorescent UV tube lamp (Lifetime: about 1,000 hours) *2 | |
Interface | USB2.0 | |
Applicable standard | VCCI class A, CE Marking, CB Report, UL, RoHS Directive, Machinery Directive | |
Power specification | AC 200 - 240 V 50/60 Hz | |
Power consumption | 7.2 kVA or less | |
Operational environment | Temperature | 20 ℃ - 30 ℃ |
Humidity | 35 - 65 %Rh | |
Dust | Equivalent to normal office level | |
Dimensions (W X D X H) (*3) | 3,852×1,977×1,690mm | |
Weight (*3) | 800kg |
*1 MCT works only with white ink.
*2 Reference value. There is no guarantee as to the lifetime.
*3 Ink Station is not included in the dimensions and the weight.
・Every UV ink is sold by the litter. Please put it into the Ink Station.
・As ink flexibility of LUS-120, LUS-150, LUS-200 may vary according to the substrate, please verify your substrate in advance.
・Inks would not be cured when printing speed is faster than that of draft mode.
LUS-120 [C,M,Y,K,W] |
C M Y K |
---|---|
C M Y K W | |
LUS-150 [C,M,Y,K,Lc,Lm,W] |
C M Y K |
C M Y K Lc Lm | |
C M Y K W | |
LUS-200 [C,M,Y,K,W] |
C M Y K |
C M Y K W |
Inks and substrates:
Safety notice:
You are dealing with UV light sources that may harm your health. Please follow below guidelines strictly:
Information |
My Account |
Connect With UsSecure Payment |
GET THE APPOcean Printer App is now available on Google Play & App Store. |